Milling Pockets and Outlines from a Drawing
On a CNC mill, the control knows where the walls of a pocket are, and it stops the cutter at them. On a manual mill, you normally have to do that part yourself: find the machine coordinate of each wall, offset it by the cutter radius, and watch the readout as you crank toward it. On a slanted or curved wall, the number you need changes every time you move the other axis, so you end up sneaking up on the line by eye.
With the "Mill to Contour" function, you can select a pocket or an outline on an imported drawing and see, on the X and Y readouts, how far the cutter can travel along each axis before it touches the wall. You keep your hands on the handwheels and crank each axis down to zero. TouchDRO accounts for the round cutter, so on a slanted or curved wall the number is the distance to where the edge of the cutter will actually touch, calculated against the drawing's true lines, arcs, and curves.
Before You Start
The "Mill to Contour" function works on a milling machine profile, in the graphical view's XY plane, in cutting mode, with a drawing on the screen. It is not offered on a lathe or in measurement mode. The drawing comes from the "CAD Drawing Import" function, and the numbers are only as good as its placement: if the drawing isn't placed on the part correctly, the walls TouchDRO measures to aren't where the part's walls are. TouchDRO has no way to check this, so it is worth confirming one corner or one hole against the part before you cut.
Before you turn the function on, apply the cutter in "Tool Compensation", and set a finish allowance there if you want to leave stock for a finishing pass. TouchDRO treats the cutter as a plain cylinder of the diameter you entered.
Selecting the Lines
The lines you select are the walls TouchDRO will guide the cutter to. You don't have to select anything, since TouchDRO can pick the area around the cutter for you, as described in "Turning the Function On" below. Selecting the lines yourself is useful when the area you want isn't the smallest one around the cutter, when a side should stay open, or when the pocket has islands in it.
To select a line, tap it. TouchDRO follows the line through simple corners and stops where three or more lines meet, at an open end, or where the selection gets back to where it started, so a clean rectangle takes one tap. To remove one segment from the selection, tap the selected segment again. This is how you leave one side of a shape open.
Long-pressing gives you the rest of the selection commands:
- On an empty area of the drawing, a long-press opens the "Canvas Commands" dialog. With "Select Enclosing Shape", you select the smallest closed area around the point you pressed, and with "Deselect All", you clear the selection. The same dialog also has "Add Guide" and "Add Sub-Datum".
- On a selected line, a long-press gives you "Deselect this Segment", and "Deselect Shape", which clears everything selected that touches that line.
TouchDRO selects what you see on the screen, regardless of how the file is built. For example, a line drawn twice in the file, one copy on top of the other, behaves as one line. Lines on a layer or in a line style you have hidden in the "Display" panel can't be selected, and "Select Enclosing Shape" passes over them, so hiding the construction lines first makes the drawing easier to work with.
Selecting Islands and Bosses
An island inside a pocket, such as a boss you are milling around, is a wall only when it is selected. "Select Enclosing Shape" and the automatic pick both select the outer boundary only, so TouchDRO would then draw the cuttable area right over the boss and let the readouts count past it.
Turning the Function On
The "Mill to Contour" button is in the column of mode buttons along the left edge of the projection view. To turn the function on, tap the button. With lines selected, TouchDRO will use the selection. With nothing selected, it will pick the smallest closed area around the cutter that the cutter fits in, and select it, so you can see what it picked. Lines the cutter is sitting on are passed over, so a construction line running through a pocket doesn't stop it from finding the pocket.
For the automatic pick, the cutter has to be inside a closed area of the drawing. With the cutter outside every outline, for example when you want to mill around the outside of a part, TouchDRO will tell you "The cutter is outside every closed area in the drawing", and you need to select the outline first. If the lines around the cutter leave a gap, you will see "The lines around the cutter don't close into an area" instead. In that case, select the lines to work along, or close the gap in the drawing.
TouchDRO also needs to know which side of the lines the cutter is on. With the center of the cutter right on a line, you will see "The cutter is on a line, so TouchDRO can't tell which area to use", and moving the cutter off the line is enough. With the cutter overlapping the lines and no closed area around it big enough for the cutter, TouchDRO will tell you so, and you need to select the lines to work along.
Whether you select the lines or let TouchDRO pick them, the cutter has to fit in the area. If it doesn't fit anywhere, TouchDRO will tell you "The cutter doesn't fit anywhere inside this area". If it would fit without the finish allowance, the message says "there is no room left for the finish allowance", so you know that a smaller allowance would be enough. When TouchDRO refuses an area it picked for you, it clears that selection, so the next tap starts from wherever the cutter is then.
To turn the function off, tap the button again.
What You See While Cutting
While the "Mill to Contour" function is on, TouchDRO changes the graphical view and the X and Y readouts to show you where the cutter can go and how far it is from the wall. Turning the function off returns the readouts to exactly what they showed before.
The Cuttable Shape
TouchDRO draws the area the cutter can actually reach in green, and the drawing's own lines go back to their usual color. Corners the cutter can't get into are rounded to its radius, and slots narrower than the cutter are left out. If a narrow neck splits the area into separate pieces, the pieces the cutter is not in are dimmed. TouchDRO assumes you will raise Z to cross from one piece to another.
With a finish allowance set, a shaded band inside the green outline shows you the stock you are leaving, as wide as the allowance.
The Readouts and Contact Lines
The X and Y readouts show the distance to the wall. Each one counts down to 0 as the cutter, together with the finish allowance, reaches the wall, and turns red and reads negative if you go past it. The readout mode button reads "incr" while the function is on.
For each axis, TouchDRO draws a dotted line from the cutter to the point on the wall that axis is measuring to, with a dot on the wall. On a slanted or curved wall, the dot sits off the crosshair, at the point where the cutter will actually touch. Once you are past the wall, the dot turns red and the line is no longer drawn.
The cutter's offset direction in Tool Compensation follows the wall as well. For each axis, TouchDRO turns the radius compensation to face the wall it is measuring to, and puts the directions back when you turn the function off.
Which Wall Each Axis Measures To
Each axis measures to the nearer of the two walls along that axis. It switches to the other wall once the cutter has passed the midpoint between them by 0.004 in (0.1 mm), so the number never jumps while you are close to a wall, and the dotted line jumps to the other wall when it does switch. On a slanted wall, the midpoint depends on where the other axis is, so moving the other axis can move the midpoint and switch the wall.
Pockets, Outlines, and Open Selections
TouchDRO uses the side of the line the center of the cutter is on as the side being cut, so there is no separate pocket or profile setting. With the cutter inside a closed outline, you are milling a pocket, and with the cutter outside it, you are milling the outline. To switch from one to the other, raise Z and move the cutter across the line.
An open selection works the same way. The selected walls get their rounded corners on the cutter's side, and the open side stays open, so you can mill a step or a slot that runs off the edge of the part.
The Proximity Warning
With the automatic proximity warning switched on, TouchDRO beeps as the cutter gets close to the wall. The button for it is the one marked with a speaker in the same column as the "Mill to Contour" button. The beep follows the axis you are cranking: it sounds only while an axis is moving toward its wall, stops about half a second after you stop, and stays quiet for an axis you are moving away from a wall. With both axes moving, the axis closer to its wall sets the beep. With the automatic proximity warning switched off, the function stays silent.
The distance at which the beeping starts is the "Warning Distance" setting of each axis, described in the "Axis Settings" guide. A near-zero warning you armed by hand in the "Axis Details" dialog is replaced while the function is on, and stays off after you turn the function off.
Finish Allowance
A finish allowance is the stock you leave on the walls for a finishing pass. You can set it in the "Tool Compensation" dialog, directly under the tool diameter. With an allowance set, TouchDRO draws a dashed ring around the cutter, and the readouts reach 0 when that ring touches the wall, so the cutter itself stops short of the wall by the allowance.
Since the allowance belongs to the applied cutter, it stays when you change tools, which suits the common case of roughing and finishing with the same end mill. For the finishing pass, clear the allowance, or set it to 0, and cut to zero again.
There is no allowance on the floor of the pocket. To leave stock on the floor, stop Z short of your depth.
Working on a Rotary Table
With "Rotate Part" linked to a rotary table encoder, the drawing turns with the table, and the distances follow it. This way, you can mill a pocket or an outline on a part turned on the table while you move the table. Note that this depends on the table's center being set accurately, which TouchDRO can't check.
While the Function Is On
While the function is on, TouchDRO protects the drawing and the readouts from changes that would make the numbers wrong:
- Taps on drawing lines, points, and guides are refused with the error sound. Long-press menus still open, and "Deselect All" turns the function off before it clears the selection.
- Picking a point or a guide from the sub-datum list turns the function off and shows that target's distance instead.
- Zero, half, hold, or setting a value on the X or Y readout turns the function off first, so the press does what it says.
- Point snap, guide snap, automatic tool offset, auto zero, and auto sub-datum are dimmed, and come back when you turn the function off. In the "Tool Compensation" dialog, the offset direction pads are dimmed, while changing the tool is still allowed.
- Hiding the drawing, hiding a layer or a line style the selected lines are on, editing or deleting a drawing line, and clearing or importing a drawing are refused with "These lines are part of the shape you are cutting". To make the change, turn the function off first. Dimming the drawing and hiding other layers are allowed.
A few changes turn the function off instead of being refused. If the drawing it is using changes, TouchDRO turns the function off and tells you that the drawing changed. If you switch the graphical view to another plane, it does the same, since the function is available only in the XY plane. In both cases, the readouts go back to what they showed before, and you can turn the function on again once the drawing or the plane is back.
Turning the tablet between portrait and landscape keeps the function on, as long as the new screen shows the graphical view. A screen without the drawing turns it off, and TouchDRO will tell you so and remind you that the readouts show your own zero again. To turn the function back on, open the graphical view. TouchDRO remembers the selection for each workspace, across screens and restarts of the app, but the function itself starts off after a restart. With the adapter disconnected, everything stays at the last known position, and you can still turn the function on to look over a drawing.
How to Use
To mill a pocket from a drawing, follow these steps:
- Import the drawing and place it on the part, as described in "CAD Drawing Import"
- Apply the cutter in "Tool Compensation", and enter a finish allowance if you want to leave stock for a finishing pass
- Move the cutter over the pocket, then raise it clear of the part
- If the pocket has bosses or islands, tap the pocket's outline and then the outline of each island
- Tap the "Mill to Contour" button
- Lower the cutter to depth, then crank one axis at a time and watch its readout count down to 0
To mill the outside of a part, tap its outline to select it, move the cutter outside the outline, and turn the function on. TouchDRO will guide the cutter around the outside of the selected lines.